Search results

Very possible.

http://cgi.ebay.com/ebaymotors/Yamaha-Warrior-Foot-Gaurds-made-from-050-aluminum_W0QQitemZ230214665920QQcmdZViewItem?hash=item230214665920

For the riding I do I need taller bars. I too ride snowmobile and need on average 4-6" of rise to be able to jump and carve. I mainly just fart around in our pits, wheelie small jumps and stuff, Where taller bars are needed so I dont cramp my back. I really dont notice that much of a...

I have 20" GBC mudsharks, I can go as far as my moms sportsman when shes in 4x4 sometimes

Im almost positive thats a member on this site, he had a few months fof or something, and his neighbor made him a bet he couldnt do it, its only a few pages back I believe, theres pictures too. cost him very little.

Think of it this way, bore it out 2mm (366 kit), put a .430 cam and a high comp piston, and its even better than new.

The raptor bars a 143 mm High, 1 mm = 0.0393700787 inch 143x.0393700787 = 5.62" Youll be fine, I have a 1" riser ontop of my moose bars, most cables have enough slack for 2-3" and then you can still re-route cables for another inch or so.

have you though of finding a straighter (or perfectly straight) bar and then going with the rox 5.5 pivot riser? I have a set of moose bars on mine and a 1" block riser. If I had the time and money I would try and find a straight bar and go with those risers its completely articulating. I...

It's on my Favorites for my Birthday parts. Nitrous, sweeeet.

http://cgi.ebay.com/ebaymotors/Mod-Quad-billet-Yamaha-Raptor-660-660r-BLUE-case-saver_W0QQcmdZViewItemQQcategoryZ43977QQihZ016QQitemZ260211420509QQrdZ1QQsspagenameZWDVW for a raptor

I've seen a few race bikes with them, personally, I like/keep my rims clean enough and shiny so I want to show them off.

What do you do? water and scrub, with all the elbow grease or gthrow the gallon on and spray off? What about a presure washer? just to the block/case and not carb area.

I wish aerodyne (I think its aerodyne) made turbo's for the warrior.

^^No way in hell im paying 60 bucks for it though. Theres billet polished ones for less than that.

Take off your seat. Take off your airbox lid. Take out your airfilter. Oil new K&N (aerosol canned K&N oil, just spray evenly over all) and place it in. Then take out your carb and install a jet-kit, or do some personal fine tuning if you have the time (on carb) . I dont know if the rappys...

Clean your connections, move your starter soleniod, disconnect, clean and tap the bottom of your solenoid with a screwdriver. Dont ask me what it does, but it worked on my TT-R.

Ill throw the link up in my signatures on my other forums. I dont know alot of people with warriors.

GO ON EBAY EXPRESS> TYPE IN WARRIOR 350 CLUTCH LEVER> GO DOWN UNTIL YOU SEE THE MSR EZ PULL ONE. ITS EZ TO PULL.

http://item.express.ebay.com/_ATV-Parts-Accessories__MSR-Raptor-EZ-pull-clutch-lever-Yamaha-Warrior-350_W0QQitemZ230197898669QQihZ013QQadnZATVQ20PartsQ20Q26Q20AccessoriesQQptdiZ2869QQcmdZExpressItem AND ITS ON CLEARENCE You can thank me later.