Said goodbye to #5 today and picked up a low hour 99 Wolverine 4x4

[YAMAHAULER]

Yeah I guess we'll see
You wouldn't happen to know what the stock jets ate suppose to be in this thing would ya?
It's got a 42.5 pilot and 140 main

 

[88WarriorBoy]

R.I.P. #5 we can only hope the new owner will take just as good of care of it as you did.

 

[Gen1Pat]

I have to I'm feeling like **** getting rid of #5 I been having 2nd thoughts all damn day
I'm a ******* idiot!!!

And, this is why I haven't sold my Warrior yet.

I don't know if the YFZ shock will fit. But, the Wolverine NEEDS better shocks, period!

 

[YAMAHAULER]

The front stockers on this are 16" eye to eye

 

[ChunkyB]

You need these elkas I have on the front of that beast. That front end would be butter smooth. I see a lot of potential in that wolverine looks racey stock,but if your having second thoughts ill trade you my warrior for it lol Come on over to the east coast

 

[2000]

Yeah I guess we'll see
You wouldn't happen to know what the stock jets ate suppose to be in this thing would ya?
It's got a 42.5 pilot and 140 main

I have no clue

 

[Gen1Pat]

Jetting sounds stock to me. After all, it is a Warrior based engine.

 

[YAMAHAULER]

I can't figure out why when I rev it up it hangs for a bit before idling down to normal
And I'm certain it's not the cable

 

[YAMAHAULER]

It's a 34mm Mikuni

 

[2000]

I can't figure out why when I rev it up it hangs for a bit before idling down to normal
And I'm certain it's not the cable

How much free play is on the lever?

 

[88WarriorBoy]

try a fatter pilot jet Ed or there is an air leak

 

[YAMAHAULER]

About 3/16

 

[Gen1Pat]

make sure the idle mixture screw is adjusted to spec. If it persists after adjusting it, do a plug chop. You may just have to adjust the mixture screw. Also, if that is a CV style carb, you may want to make sure the vacuum diaphram is good, and that the slide moves freely.

 

[YAMAHAULER]

I would adjust to spec if I knew what it's suppose to be right now I have it at 2 turns out
The diaphram is good and slide moves freely plug is showing rich but no issues through throttle range

 

['00 WO-YA!]

We're talking about Pat^ here right. For him I'd say, money, sex, rolling rock or Javelin parts, lol!

 

[YAMAHAULER]

Front wheel bearings & seals kit by American Star and All Balls front drive shaft U - joint came today and hopefully the rear axle bearings and seals will be here tomorrow

 

[YAMAHAULER]

She's a Tank now ! And it shifts so much smoother and easier now too

 

[Gen1Pat]

We're talking about Pat^ here right. For him I'd say, money, sex, rolling rock or Javelin parts, lol!

Huh??? I'm lost on this one. Although I would say it's accurate, whatever it is, and in just about the right order!!




Ed, two turns out is probably about right. Try running it at 1.5 and recheck the plug. If the filter is good and clean, I'd say take it down one jet size and recheck again.

 

[YAMAHAULER]

I ordered a ngk Iridium IX plug at Advance will be there in morning so I'll try a new plug first since this one is a bit fouled
When I rev it up it snaps and pops on decell not a lot just 1 or 2 pops

 

[YAMAHAULER]

And I changed out the stock filter foam with the moose racing stock equivalent foam cause it was bad