What did you do to your quad today?

[DeadLastRacing]

what bore size/comp is it?

All info in the FS section.

 

[alex456123]

All info in the FS section.

k cool.

 

[bones]

or you can ship me to canada to push you round! you get to ride the warrior and i have a free weight loss program. win-win!

i thought we covered this ... freight shipping is pricey.... especially when crossing boarders !!

 

[lbjamm]

^ haha Alex, he call you fatboy

 

[lbjamm]

Well I went outside, and sat on mine for a minute, and made "bing da ding ding" sounds.. lol

Yah, I like to sit on mine and make vroom vroom sounds too.

 

[alex456123]

Yah, I like to sit on mine and make vroom vroom sounds too.

yeah its fun isnt it!

 

[PHANTOMLORD]

I fire mine up, warm it and juice it a few times and then back into the house, do alot of stairing at it too, my wife says she dont understand what im doing i tell her im fixing it, but in my mind,,:haha:

 

[sparkymichigan]

Adjusted my front Works, 2 3/4" sag. Works should have done better on how to adjust them. Moving a clip sucks.

 

[liftedhigh]

Today I did:

Wifes Warrior: Rebuilt Carburetor, installed new (to me) rear break, installed new intake manifold.

Daughters 50cc: tore wiring harness apart and re wired it

My bike: looked at the new Banshee front shocks for it but didn't touch it.

Tomorrow I have to go get a vacuum pump to try and draw brake fluid into the rear cliper since I get pump any back there. Maybe I'll put my shocks on too.

 

[buzzy613]

well yesterday i tried to adjust the float on the carb but i dont think i had success, tomarow im going to fire it up and take it for a drive if i pick up gas. and mabey take it out to the bay some time soon

 

[PHANTOMLORD]

Lifted leave the resivor cap off and open the bleeder and let it gravity bleed till you get some fluid back there then do your pump bleeding, i no this works on cars but not sure on a bike!!!
I just got in from putting my new nerfbars on and the heel guards and shields, also put on the new exhaust pipe band clamp but is leaking so ill have to go back to that one..

 

[liftedhigh]

I have had the brake line just laying there in the back not attached to the caliper and with the lid off for 3 days and not even a drop on the ground. I'm gonna try to vacuum bleed tomorrow and if that doesn't work I will rebuild the master. I know fluid is getting to the master just not past it.

 

[alex456123]

I have had the brake line just laying there in the back not attached to the caliper and with the lid off for 3 days and not even a drop on the ground. I'm gonna try to vacuum bleed tomorrow and if that doesn't work I will rebuild the master. I know fluid is getting to the master just not past it.

i had this problem too so i did the vacuum bleed and it worked. :tup:

 

[beastlywarrior228]

I've got a reverse bleeder

 

[PHANTOMLORD]

Like i said "didnt no if its the same as a car"..gess not then..

 

[buzzy613]

made vroom sounds lol

 

[JakeBloom]

Stared at it and wished that my yz250 shifter would come sooner.

 

[alex456123]

Stared at it and wished that my yz250 shifter would come sooner.

lol

 

[buzzy613]

started to get measurements and ideas to start drawing up ideas on hoe i want to make my bars

 

[S.E.Warrior97-2001]

I may be considered a puddar on here but its to damn cold out there, been about 25 all day